Hej , jag har ett monoblock JBL: GTO-14001 - med följande spec
1200 watts RMS x 1 channel at 4 ohms
1500 watts RMS x 1 channel at 2 ohms & 14.4V supply
Max Power: 1500 watts at 4 ohms
DBO (Dynamic Bass Optimization)
Low Pass Filter Frequency control
12dB Octave Low pass filter variable 32Hz-320Hz
Maximum Input Signal: 4.7V
Maximum Sensitivity: 220mV
Output Regulation: .098 dB at 4 ohms
Signal-to-Noise (dBA) 104dBA (reference rated power into 4 ohms)
THD 0.04% (rated power at 4 ohms)
Frequency Response 20Hz - 330Hz (-3dB)
Dimensions L x W x H) 18-9/16" x 10-3/8" x 2-1/8"
Tänkte koppla in 2 st 12 tums basar och står mellan
1) 2 st JBL: W12GTi MKII - 12 ( 3ohms eller & Ohms)
koppla 2 st i 3 ohms så att det blir 1.5 Ohm mot steget
Spec
12" GTi MKII Differential Drive® Design Subwoofer
Dual Voice coil design (dual 6-ohm, pre-wired as a 3-ohm sub)
Differential Drive® Design (DDD) motor
Die-cast vented basket
Kevlar®-impregnated paper woofer cone
Nitrile-butylene surround
Power handling RMS: 700 watts
Power handling Peak: 4,000 watts
Sensitivity 91dB @ 2.83V/1m
Power Handling 700W RMS, 4,000W Peak
Frequency Response 18Hz ~ 1kHz
Impedance 3 or 12 ohms
Voice-Coil Diameter 3" (76mm)
Mounting Depth 10-1/4" (260mm)
Overall Diameter 12-1/4" (312mm)
Cut-Out Diameter 11" (280mm)
Displacement 0.149 ft3 (4.23 l)
2) 2 st KICKER-08S12L72-2008-RANGE ( 2 ohms eller 4)
Koppla 2 i 4 ohms så att det blir 2 Ohm mot steget
Size (IN., CM): 12", 30cm
Impedance: Dual 2-ohms (can be wired as 1-ohm or 4-ohms)
Square SoloKon™ polypropylene cone with Santoprene rubber surround
Sealed Box Volume (cu ft) 0.88-2.0
Ported Box Volume (cu ft) 1.75-3.25
Sensitivity 88.6dB
Frequency Response 20-100 Hz
RMS Power Range (Watts) 750
Peak Power Handling (Watts) 1500
Top Mount Depth (inches) 6-13/16"
Cutout Diameter or Length (inches) 11-1/16
Finns det någon så skulle kunna hjälpa mig med vilka jag ska välja ,
//kostas
1200 watts RMS x 1 channel at 4 ohms
1500 watts RMS x 1 channel at 2 ohms & 14.4V supply
Max Power: 1500 watts at 4 ohms
DBO (Dynamic Bass Optimization)
Low Pass Filter Frequency control
12dB Octave Low pass filter variable 32Hz-320Hz
Maximum Input Signal: 4.7V
Maximum Sensitivity: 220mV
Output Regulation: .098 dB at 4 ohms
Signal-to-Noise (dBA) 104dBA (reference rated power into 4 ohms)
THD 0.04% (rated power at 4 ohms)
Frequency Response 20Hz - 330Hz (-3dB)
Dimensions L x W x H) 18-9/16" x 10-3/8" x 2-1/8"
Tänkte koppla in 2 st 12 tums basar och står mellan
1) 2 st JBL: W12GTi MKII - 12 ( 3ohms eller & Ohms)
koppla 2 st i 3 ohms så att det blir 1.5 Ohm mot steget
Spec
12" GTi MKII Differential Drive® Design Subwoofer
Dual Voice coil design (dual 6-ohm, pre-wired as a 3-ohm sub)
Differential Drive® Design (DDD) motor
Die-cast vented basket
Kevlar®-impregnated paper woofer cone
Nitrile-butylene surround
Power handling RMS: 700 watts
Power handling Peak: 4,000 watts
Sensitivity 91dB @ 2.83V/1m
Power Handling 700W RMS, 4,000W Peak
Frequency Response 18Hz ~ 1kHz
Impedance 3 or 12 ohms
Voice-Coil Diameter 3" (76mm)
Mounting Depth 10-1/4" (260mm)
Overall Diameter 12-1/4" (312mm)
Cut-Out Diameter 11" (280mm)
Displacement 0.149 ft3 (4.23 l)
2) 2 st KICKER-08S12L72-2008-RANGE ( 2 ohms eller 4)
Koppla 2 i 4 ohms så att det blir 2 Ohm mot steget
Size (IN., CM): 12", 30cm
Impedance: Dual 2-ohms (can be wired as 1-ohm or 4-ohms)
Square SoloKon™ polypropylene cone with Santoprene rubber surround
Sealed Box Volume (cu ft) 0.88-2.0
Ported Box Volume (cu ft) 1.75-3.25
Sensitivity 88.6dB
Frequency Response 20-100 Hz
RMS Power Range (Watts) 750
Peak Power Handling (Watts) 1500
Top Mount Depth (inches) 6-13/16"
Cutout Diameter or Length (inches) 11-1/16
Finns det någon så skulle kunna hjälpa mig med vilka jag ska välja ,
//kostas

Som det blir med dubbla 6 ohmsspolar.
Comment